INDICATOR CONTROLLER

UT-1801/2/3

  • LARGE DISPLAY INDICATOR

     

    ♦ Large LED display size 2”/4”/6”/8”/12”/16” available.

    ♦ IP-55 and IP-65 housing available.

    ♦ Hanging/Rack/wall/panel mounting available as options.

    ♦ Universal Input T/C, RTD, Linear input selection.

    ♦ Hi brightness LED For long distance and Batter Visualization

    ♦ All Configurations and calibration from front panel keypad.

    ♦ Retransmission 4-20mA available.

  •  FEATURE

     

    ♦ Large display size 2”/4”/6”/8”/12”/16” available.

    ♦ Large display size for easy viewing from a distance.

    ♦ IP-55 and IP-65 housing available.

    ♦ Hanging /Rack/wall/panel mounting options.

    ♦ µP Based Power, full & highly reliable controller.

    ♦ Universal Input T/C, RTD, Linear input selection.

    ♦ Potential Free Relay contact output up to 1 / 2 / 3 / 4.

    ♦ 0.1% Accuracy of FSD.

    ♦ All Configurations and calibration from front panel keypad.

    ♦ Highly communicative serial interface facility (RS 232/485).

    ♦ Power supply :230V/110V AC or 24V/12V DC.

    ♦ Optional GSM mobile connectivity.

    ♦ Fully Password Protected Operation.

► INPUT

T/C - K, J, R, S, E, N, T

RTD - Pt-100, Cu53 ( 2wire & 3 wire)

Current - 0 ~ 20mA DC, 4~20mA DC

Voltage - 0-5V/1-5V, 0.5 -2.5V/0- 10 V DC

Special on demand - 0-75/200 mV & 0-1/10V/100/300 V DC

Transmitter power supply -0-75/200 mV 0-100/300V DC Resistence - 0-500 k , 0-1/5/10/100 K

Cold junction comp. & Sensor break ind. -10/12/24 V DC @ 30 mA max, isolated from I/p & O/P

Range limits - Software base Automatic.

Accuracy - As per input range Table.

Impedance - +/- 0.1 % of span for linear & RTD, +/-0.25 % for T/C.

Display Indication - >330 K for Voltage ,mV, and T/C, 100 R for current.

► INDICATION CONTROL MODE

Status indication -1” ,2” ,4” (7 segments block type), 6” ,8”, 12” ,16” (7 segment Led type)

On Off control - LEDs for Relay status & Communications.

► OUTPUT

Relay Output -NO - C - NC Contacts , 5A@240 V AC Resistiv , 1 / 2 / 3 / 4 Relays / SSR output

SSR Output -24VDC @ 20 mA ,12VDC @ 20 mA

Retransmission Current & Voltage outputs -0~20/ 4~20 mA,0~5V, 0~10V, 1~5V DC, fully 3 port isolated 1.5KV

► COMMUNICATION

Retransmission Current & Voltage outputs -0~20/ 4~20 mA,0~5V, 0~10V, 1~5V DC, fully 3 port isolated 1.5KV.

Communication Protocol & mathod -Modbus RTU RS- 485/RS- 232 Communication.

Programmable & ma Connectable number -Baud rate,Parity , Node address , Stop bit & 0-256 unit.

► PROGRAMMBALE PARAMETERS

Wireless Communication -GSM/GPRS base mobile(sms) Communication.

Set point / High scale / Low scale -Full range as per input selection.

Relay Logic -F.S. high & low alarm , Dead band alarm

Display resolution --1999 to 9999 fully configurable for linear input

Programming of parameters -Through 4 tactile keys

► Other

Dimensions Mounting -Wall mounting/ base mounting/ panel mounting and hanging type.

Supply voltage -110/230 AC , 50/60 Hz.

Power consumption -4 watts maximum.

Operating ambient temperature and humidity - 0~50 °C , Below 90%, non condensing